BESS Working Group
Internet Engineering Task Force (IETF) P. Brissette
Internet-Draft
Request for Comments: 9786 LA. Burdet, Ed.
Intended status:
Category: Standards Track Cisco Systems
Expires: 8 June 2025
ISSN: 2070-1721 B. Wen
Comcast
E. Leyton
Verizon Wireless
J. Rabadan
Nokia
5 December 2024
May 2025
EVPN Port-Active Redundancy Mode
draft-ietf-bess-evpn-mh-pa-13
Abstract
The Multi-Chassis Link Aggregation Group (MC-LAG) group technology enables
establishing a logical link-aggregation connection with a redundant
group of independent nodes. The objective of MC-LAG is to enhance
both network availability and bandwidth utilization through various
modes of traffic load-balancing. RFC7432 load balancing. RFC 7432 defines an EVPN-based MC-LAG MC-
LAG with Single-active Single-Active and All-active All-Active multi-homing redundancy modes.
This document builds on the existing redundancy mechanisms supported
by EVPN and introduces a new active/standby redundancy mode, called
'Port-Active'.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 8 June 2025.
https://www.rfc-editor.org/info/rfc9786.
Copyright Notice
Copyright (c) 2024 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
1.2. Multi-Chassis Link Aggregation (MC-LAG) . . . . . . . . . 3
2. Port-Active Redundancy Mode . . . . . . . . . . . . . . . . . 4
2.1. Overall Advantages . . . . . . . . . . . . . . . . . . . 4
2.2. Port-Active Redundancy Procedures . . . . . . . . . . . . 5
3. Designated Forwarder Algorithm to Elect per Port-Active PE . 6
3.1. Capability Flag . . . . . . . . . . . . . . . . . . . . . 6
3.2. Modulo-based Modulo-Based Algorithm . . . . . . . . . . . . . . . . . 7
3.3. Highest Random Weight Algorithm . . . . . . . . . . . . . 7
3.4. Preference-based Preference-Based DF Election . . . . . . . . . . . . . . 8
3.5. AC-Influenced DF Election . . . . . . . . . . . . . . . . 8
4. Convergence considerations . . . . . . . . . . . . . . . . . 8 Considerations
4.1. Primary / Backup Primary/Backup Bits per Ethernet-Segment . . . . . . . . . . 9 Ethernet Segment
4.2. Backward Compatibility . . . . . . . . . . . . . . . . . 10
5. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 10
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
7. Security Considerations . . . . . . . . . . . . . . . . . . . 11
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 11
9. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 11
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 11
10.1.
8.1. Normative References . . . . . . . . . . . . . . . . . . 11
10.2.
8.2. Informative References . . . . . . . . . . . . . . . . . 12
Acknowledgements
Contributors
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 13
1. Introduction
EVPN [RFC7432] defines the All-Active and Single-Active redundancy
modes. All-Active redundancy provides per-flow load-balancing load balancing for
multi-homing, while Single-Active redundancy ensures service carving
where only one of the Provider Edge (PE) devices in a redundancy
relationship is active per service.
Although these two multi-homing scenarios are widely utilized in data
center and service provider access networks, there are cases where
active/standby multi-homing at the interface level is beneficial and
necessary. The primary consideration for this new mode of load- load
balancing is the determinism of traffic forwarding through a specific
interface,
interface rather than statistical per-flow load-balancing load balancing across
multiple PEs providing multi-homing. This determinism is essential
for certain QoS features to function correctly. Additionally, this
mode ensures fast convergence during failure and recovery, which is
expected by customers.
This document defines the Port-Active redundancy mode as a new type
of multi-homing in EVPN and details how this mode operates and is
supported via EVPN.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
1.2. Multi-Chassis Link Aggregation (MC-LAG)
When a CE Customer Equipment (CE) device is multi-homed to a set of PE
nodes using the
[IEEE_802.1AX_2014] Link Aggregation Control Protocol (LACP), (LACP)
[IEEE_802.1AX_2014], the PEs must function as a single LACP entity
for the Ethernet links to form and operate as a Link Aggregation
Group (LAG). To achieve this, the PEs connected to the same multi-homed multi-
homed CE must synchronize LACP configuration and operational data
among them. Historically, the
Interchassis Inter-Chassis Communication Protocol
(ICCP) [RFC7275] has been used for this synchronization. EVPN, as
described in [RFC7432], covers the scenario where a CE is multi-homed
to multiple PE nodes, using a LAG to simplify the procedure
significantly. This simplification,
however, However, this simplification comes with certain
assumptions:
* a A CE device connected to EVPN multi-homing PEs MUST have a single
LAG with all its links connected to the EVPN multi-homing PEs in a
redundancy group.
* identical Identical LACP parameters MUST be configured on peering PEs,
including the system ID, port priority, and port key.
This document presumes proper LAG operation as specified in
[RFC7432]. Issues resulting from deviations in the aforementioned
assumptions, LAG misconfiguration, and miswiring detection across
peering PEs are considered outside the scope of this document.
+-----+
| PE3 |
+-----+
+-----------+
| MPLS/IP |
| CORE |
+-----------+
+-----+ +-----+
| PE1 | | PE2 |
+-----+ +-----+
I1 I2
\ /
\ /
\ /
+---+
|CE1|
+---+
Figure 1: MC-LAG Topology
Figure 1 shows a an MC-LAG multi-homing topology where PE1 and PE2 are
part of the same redundancy group providing multi-homing to CE1 via
interfaces I1 and I2. Interfaces I1 and I2 are members of a LAG
running LACP. The core, shown as IP or MPLS enabled, provides a wide
range of L2 and L3 services. MC-LAG multi-homing functionality is
decoupled from those services in the core core, and it focuses on
providing multi-homing to the CE. In Port-Active redundancy mode,
only one of the two interfaces interfaces, I1 or I2 I2, would be in forwarding forwarding, and
the other interface will would be in standby. This also implies that all
services on the active interface are operate in active mode and all
services on the standby interface operate in standby mode.
2. Port-Active Redundancy Mode
2.1. Overall Advantages
The use of Port-Active redundancy in EVPN networks provides the
following benefits:
a. Port-Active redundancy It offers open standards-based open-standards-based active/standby redundancy at the
interface level, level rather than VLAN granularity [RFC7432].
b. Port-Active redundancy It eliminates the need for ICCP and LDP
[RFC5306] [RFC5036] (e.g., VXLAN Virtual
eXtensible Local Area Network (VXLAN) [RFC7348] or SRv6 Segment
Routing over IPv6 (SRv6) [RFC8402] may be used in the network).
c. This mode is agnostic of the underlying technology (MPLS, VXLAN,
and SRv6) and associated services (L2, L3, (Layer 2 (L2), Layer 3 (L3),
Bridging, E-LINE, etc.)
d. It enables deterministic QoS over MC-LAG attachment circuits.
e. Port-Active redundancy It is fully compliant with [RFC7432] and does not require any new
protocol enhancements to existing EVPN RFCs.
f. It can leverage various Designated Forwarder (DF) election
algorithms, such as modulo ([RFC7432]), [RFC7432], Highest Random Weight
(HRW, [RFC8584]), (HRW)
[RFC8584], etc.
g. Port-Active redundancy It replaces legacy MC-LAG ICCP-based solutions and offers the
following additional benefits:
* Efficient support for 1+N redundancy mode (with EVPN using BGP
Route Reflector), whereas ICCP requires a full mesh of LDP
sessions among PEs in the redundancy group.
* Fast convergence with mass-withdraw mass withdraw is possible with EVPN,
which has no equivalent in ICCP.
2.2. Port-Active Redundancy Procedures
The following steps outline the proposed procedure for supporting
Port-Active redundancy mode with EVPN LAG:
a. The Ethernet-Segment Ethernet Segment Identifier (ESI) MUST be assigned per access
interface as described in [RFC7432]. The ESI can be auto-derived
or manually assigned assigned, and the access interface MAY be a Layer-2 an L2 or
Layer-3 L3
interface.
b. The Ethernet-Segment Ethernet Segment (ES) MUST be configured in Port-Active
redundancy mode on peering PEs for the specified access
interface.
c. When ESI is configured on a Layer-3 an L3 interface, the Ethernet-
Segment (ES) ES route (Route
Type-4) can be the only route exchanged by PEs in the redundancy
group.
d. PEs in the redundancy group leverage the DF election defined in
[RFC8584] to determine which PE keeps the port in active mode and
which one(s) keep it in standby mode. Although the DF election
defined in [RFC8584] is per [ES, Ethernet Tag] granularity, the
DF election is performed per [ES] in Port-Active redundancy mode.
The details of this algorithm are described in Section 3.
e. The DF router MUST keep the corresponding access interface in an
up and forwarding active state for that Ethernet-Segment. ES.
f. Non-DF routers SHOULD implement a bidirectional blocking scheme
for all traffic comparable to the Single-Active blocking scheme
described in [RFC7432], albeit across all VLANs.
* Non-DF routers MAY bring and keep the peering access interface
attached to them in an operational down state.
* If the interface is running the LACP protocol, the non-DF PE
MAY set the LACP state to OOS (Out Out of Sync) Sync (OOS) instead of setting
the interface to a down state. This approach allows for
better convergence during the transition from standby to
active mode.
g. The primary/backup bits of the EVPN Layer 2 Attributes (L2-Attr)
Extended Community [RFC8214] SHOULD be used to achieve better
convergence, as described in Section 4.1.
3. Designated Forwarder Algorithm to Elect per Port-Active PE
The Ethernet-Segment (ES) ES routes operating in Port-Active redundancy mode are advertised
with the new Port Mode Load-Balancing capability bit in the DF
Election Extended Community as defined in [RFC8584]. Additionally,
the ES associated with the port utilizes the existing Single-Active
procedure and signals the Single-Active Multihomed multi-homed site redundancy
mode along with the Ethernet-AD Ethernet A-D per-ES route (refer to Section 7.5
of [RFC7432]). Finally, The ESI label-based split-horizon procedures
specified in Section 8.3 of [RFC7432] SHOULD be employed to prevent
transient echo packets when Layer-2 L2 circuits are involved.
Various algorithms for DF Election election are detailed in Sections 3.2 to
3.5 for comprehensive understanding, although the choice of algorithm
in this solution does not significantly impact complexity or
performance compared to other redundancy modes.
3.1. Capability Flag
[RFC8584] defines a DF Election extended community, Extended Community and a Bitmap (2
octets) field to encode "DF Election Capabilities" to use with the DF
election algorithm in the DF algorithm field:
Bit 0: D bit or 'Don't Pre-empt' Preempt' bit, as explained described in
[I-D.ietf-bess-evpn-pref-df]. [RFC9785].
Bit 1: AC-Influenced DF (AC-DF) election, as explained described in
[RFC8584].
1 1 1 1 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|D|A| |P| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Amended DF Election Capabilities in the DF Election
Extended Community
This document defines the following value and extends the DF Election
Capabilities bitmap field:
Bit 5: Port Mode Designated Forwarder Election. This bit
determines that the DF Election election algorithm SHOULD be
modified to consider the port ES only and not the Ethernet
Tags.
3.2. Modulo-based Modulo-Based Algorithm
The default DF Election election algorithm, or modulo-based algorithm, as
described in [RFC7432] and updated by [RFC8584], is applied here at
the granularity of ES only. Given that the ES-Import Route Target
extended community may be auto-derived and directly inherits its
auto-derived value from ESI bytes 1-6, many operators differentiate
ESIs primarily within these bytes. Consequently, bytes 3-6 are
utilized to determine the designated forwarder using the modulo-based
DF assignment, achieving good entropy during modulo calculation
across ESIs.
Assuming a redundancy group of N PE nodes, the PE with ordinal i is
designated as the DF for an <ES> when (Es mod N) = i, where Es
represents bytes 3-6 of that ESI.
3.3. Highest Random Weight Algorithm
An application of Highest Random Weight (HRW) to EVPN DF Election election is
defined in [RFC8584] [RFC8584], and it MAY also be used and signaled. For Port-
Active
Active, this is modified to operate at the granularity of <ES> rather
than per <ES, VLAN>.
Section 3.2 of [RFC8584] describes computing a 32-bit CRC Cyclic
Redundancy Check (CRC) over the concatenation of Ethernet Tag (V) and
ESI (Es). For Port-Active redundancy mode, the Ethernet Tag is
omitted from the CRC computation and all references to (V, Es) are
replaced by (Es).
The algorithm to detemine determine the DF Elected and Backup-DF Elected (BDF)
at Section 3.2 of [RFC8584] is repeated and summarized below using
only (Es) in the computation:
1. DF(Es) = Si| Weight(Es, Si) >= Weight(Es, Sj), for all j. In the
case of a tie, choose the PE whose IP address is numerically the
least. Note that 0 <= i,j < number of PEs in the redundancy
group.
2. BDF(Es) = Sk| Weight(Es, Si) >= Weight(Es, Sk), and Weight(Es,
Sk) >= Weight(Es, Sj). In the case of a tie, choose the PE whose
IP address is numerically the least.
Where:
* DF(Es) is defined to be the address Si (index i) for which
Weight(Es, Si) is the highest; 0 <= i < N-1.
* BDF(Es) is defined as that PE with address Sk for which the
computed Weight is the next highest after the Weight of the DF. j
is the running index from 0 to N-1; i and k are selected values.
3.4. Preference-based Preference-Based DF Election
When the new capability 'Port Mode' is signaled, the preference-based
DF Election election algorithm in [I-D.ietf-bess-evpn-pref-df] [RFC9785] is modified to consider the port only
and not any associated Ethernet Tags. The Port Mode capability is
compatible with the 'Don't Pre-empt' Preempt' bit and both may be signaled.
When an interface recovers, a peering PE signaling the D bit enables
non-revertive behavior at the port level.
3.5. AC-Influenced DF Election
The AC-DF bit defined in [RFC8584] MUST be set to 0 when advertising
Port Mode Designated Forwarder Election capability (P=1). When an AC
(sub-interface) goes down, any resulting Ethernet A-D per EVI
withdrawal does not influence the DF Election. election.
Upon receiving the AC-DF bit set (A=1) from a remote PE, it MUST be
ignored when performing Port Mode DF Designated Forwarder Election.
4. Convergence considerations Considerations
To enhance convergence during failure and recovery when Port-Active the Port-
Active redundancy mode is employed, prior synchronization between
peering PEs may be beneficial.
The Port-Active mode poses a challenge to synchronization since the
"standby" port may be in a down state. Transitioning a "standby"
port to an up state and stabilizing the network requires time. For
Integrated Routing and Bridging (IRB) and Layer 3 L3 services, prior
synchronization of ARP / ND Neighbor Discovery (ND) caches is
recommended. Additionally, associated VRF Virtual Routing and Forwarding
(VRF) tables may need to be synchronized. For Layer 2 L2 services,
synchronization of MAC tables may be considered.
Moreover, for members of a LAG running LACP, the ability to set the
"standby" port to an "out-of-sync" state, also known as "warm-
standby," can be utilized to improve convergence times.
4.1. Primary / Backup Primary/Backup Bits per Ethernet-Segment Ethernet Segment
The EVPN Layer 2 Attributes L2-Attr Extended Community ("L2-Attr") defined in [RFC8214] SHOULD be
advertised in the Ethernet A-D per ES route to enable fast
convergence.
Only the P and B bits of the Control Flags field in the L2-Attr
Extended Community are relevant to this document, specifically in the
context of Ethernet A-D per ES routes:
* When advertised, the L2-Attr Extended Community SHALL have only
the P or B bits set in the Control Flags field, and all other bits
and fields MUST be zero.
* A remote PE receiving the optional L2-Attr Extended Community in
Ethernet A-D per ES routes SHALL consider only the P and B bits
and ignore other values.
For the L2-Attr Extended Community sent and received in Ethernet A-D
per EVI routes used in [RFC8214], [RFC7432] [RFC7432], and
[I-D.ietf-bess-evpn-vpws-fxc]: [RFC9744]:
* P and B bits received SHOULD be considered overridden by "parent"
bits when advertised in the Ethernet A-D per ES.
* Other fields and bits of the extended community are used according
to the procedures outlined in the referenced documents.
By adhering to these procedures, the network ensures proper handling
of the L2-Attr Extended Community to maintain robust and efficient
convergence across Ethernet Segments.
4.2. Backward Compatibility
Implementations that comply with [RFC7432] or [RFC8214] only (i.e.,
implementations that predate this specification) which and that receive an
L2-Attr Extended Community in Ethernet A-D per ES routes will ignore
it and continue to use the default path resolution algorithms of the
two specifications above:
* The L2-Attr Extended Community in Ethernet A-D per ES route is
ignored
ignored.
* The remote ESI Label Extended Community ([RFC7432]) label extended community [RFC7432] signals
Single-Active Single-
Active (Section 3) 3).
* the The remote MAC Media Access Control (MAC) and/or Ethernet A-D per EVI
routes are unchanged, unchanged; the P and B bits in the L2-Attr Extended
Community in Ethernet A-D per EVI routes are used.
5. Applicability
A prevalent deployment scenario involves providing L2 or L3 services
on PE devices that offer multi-homing capabilities. The services may
include any L2 EVPN solutions such as EVPN VPWS Virtual Private Wire
Service (VPWS) or standard EVPN as defined in [RFC7432].
Additionally, L3 services may be provided within a VPN context, as
specified in [RFC4364], or within a global routing context. When a
PE provides first-hop routing, EVPN IRB may also be deployed on the
PEs. The mechanism outlined in this document applies to PEs
providing L2 and/or L3 services where active/standby redundancy at
the interface level is required.
An alternative solution to the one described in this document is
Multi-Chassis Link Aggregation Group (MC-LAG) MC-
LAG with ICCP active-
standby active/standby redundancy, as detailed in [RFC7275].
However, ICCP requires LDP to be enabled as a transport for ICCP
messages. There are numerous scenarios where LDP is not necessary,
such as deployments utilizing VXLAN or SRv6. The solution using
EVPN, as described in this document
using EVPN document, does not mandate the use of LDP
or ICCP and remains independent of the underlay encapsulation.
6. IANA Considerations
This document solicits the allocation of
Per this document, IANA has added the following values from entry to the "BGP "DF
Election Capabilities" registry under the "Border Gateway Protocol
(BGP) Extended Communities" registry group :
* group:
+=====+=========================================+===========+
| Bit | Name | Reference |
+=====+=========================================+===========+
| 5 in the [RFC8584] DF Election Capabilities registry, "Port | Port Mode Designated Forwarder Election". Election | RFC 9786 |
+-----+-----------------------------------------+-----------+
Table 1
7. Security Considerations
The Security Considerations security considerations described in [RFC7432] and [RFC8584] are
applicable to this document.
Introducing a new capability necessitates unanimity among PEs.
Without consensus on the new DF Election election procedures and Port Mode,
the DF Election election algorithm defaults to the procedures outlined in
[RFC8584] and [RFC7432].This fallback behavior could be exploited by
an attacker who modifies the configuration of one PE within the
Ethernet Segment (ES). ES.
Such manipulation could force all PEs in the ES to revert to the
default DF Election election algorithm and capabilities. In this scenario,
the PEs may be subject to unfair load balancing, service disruption,
and potential issues such as black-holing or duplicate traffic, as
mentioned in the security sections of those documents.
8. Acknowledgements
The authors thank Anoop Ghanwani for his comments and suggestions and
Stephane Litkowski and Gunter van de Velde for their careful reviews.
9. Contributors
In addition to the authors listed on the front page, the following
people have also contributed to this document:
Ali Sajassi
Cisco Systems
United States of America
Email: sajassi@cisco.com
Samir Thoria
Cisco Systems
United States of America
Email: sthoria@cisco.com
10. References
10.1.
8.1. Normative References
[I-D.ietf-bess-evpn-pref-df]
Rabadan, J., Sathappan, S., Lin, W., Drake, J., and A.
Sajassi, "Preference-based EVPN DF Election", Work in
Progress, Internet-Draft, draft-ietf-bess-evpn-pref-df-13,
9 October 2023, <https://datatracker.ietf.org/doc/html/
draft-ietf-bess-evpn-pref-df-13>.
[IEEE_802.1AX_2014]
IEEE, "IEEE Standard for Local and metropolitan area
networks -- Link Aggregation", IEEE 802-1ax-2014,
DOI 10.1109/IEEESTD.2014.7055197, 5 March 2015,
<https://ieeexplore.ieee.org/document/7055197>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <https://www.rfc-editor.org/info/rfc7432>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8214] Boutros, S., Sajassi, A., Salam, S., Drake, J., and J.
Rabadan, "Virtual Private Wire Service Support in Ethernet
VPN", RFC 8214, DOI 10.17487/RFC8214, August 2017,
<https://www.rfc-editor.org/info/rfc8214>.
[RFC8584] Rabadan, J., Ed., Mohanty, S., Ed., Sajassi, A., Drake,
J., Nagaraj, K., and S. Sathappan, "Framework for Ethernet
VPN Designated Forwarder Election Extensibility",
RFC 8584, DOI 10.17487/RFC8584, April 2019,
<https://www.rfc-editor.org/info/rfc8584>.
10.2. Informative References
[I-D.ietf-bess-evpn-vpws-fxc]
Sajassi, A., Brissette, P., Uttaro,
[RFC9785] Rabadan, J., Ed., Sathappan, S., Lin, W., Drake, J.,
Boutros, S., and J. Rabadan, "EVPN VPWS Flexible Cross-
Connect Service", Work in Progress, Internet-Draft, draft-
ietf-bess-evpn-vpws-fxc-10, 4 December 2024,
<https://datatracker.ietf.org/doc/html/draft-ietf-bess-
evpn-vpws-fxc-10>.
A. Sajassi, "Preference-Based EVPN Designated Forwarder
(DF) Election", RFC RFC9785, DOI 10.17487/RFC9785, May
2025, <https://www.rfc-editor.org/info/rfc9785>.
8.2. Informative References
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
2006, <https://www.rfc-editor.org/info/rfc4364>.
[RFC5306] Shand, M.
[RFC5036] Andersson, L., Ed., Minei, I., Ed., and L. Ginsberg, "Restart Signaling for IS-IS", B. Thomas, Ed.,
"LDP Specification", RFC 5306, 5036, DOI 10.17487/RFC5306, 10.17487/RFC5036,
October 2008,
<https://www.rfc-editor.org/info/rfc5306>. 2007, <https://www.rfc-editor.org/info/rfc5036>.
[RFC7275] Martini, L., Salam, S., Sajassi, A., Bocci, M.,
Matsushima, S., and T. Nadeau, "Inter-Chassis
Communication Protocol for Layer 2 Virtual Private Network
(L2VPN) Provider Edge (PE) Redundancy", RFC 7275,
DOI 10.17487/RFC7275, June 2014,
<https://www.rfc-editor.org/info/rfc7275>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
July 2018, <https://www.rfc-editor.org/info/rfc8402>.
[RFC9744] Sajassi, A., Ed., Brissette, P., Uttaro, J., Drake, J.,
Boutros, S., and J. Rabadan, "EVPN Virtual Private Wire
Service (VPWS) Flexible Cross-Connect (FXC) Service",
RFC 9744, DOI 10.17487/RFC9744, March 2025,
<https://www.rfc-editor.org/info/rfc9744>.
Acknowledgements
The authors thank Anoop Ghanwani for his comments and suggestions and
Stephane Litkowski and Gunter Van de Velde for their careful reviews.
Contributors
In addition to the authors listed on the front page, the following
people have also contributed to this document:
Ali Sajassi
Cisco Systems
United States of America
Email: sajassi@cisco.com
Samir Thoria
Cisco Systems
United States of America
Email: sthoria@cisco.com
Authors' Addresses
Patrice Brissette
Cisco Systems
Ottawa ON
Canada
Email: pbrisset@cisco.com
Luc Andre André Burdet (editor)
Cisco Systems
Canada
Email: lburdet@cisco.com
Bin Wen
Comcast
United States of America
Email: Bin_Wen@comcast.com
Edward Leyton
Verizon Wireless
United States of America
Email: edward.leyton@verizonwireless.com
Jorge Rabadan
Nokia
United States of America
Email: jorge.rabadan@nokia.com