Network Working Group
Internet Engineering Task Force (IETF) A. Bashandy
Internet-Draft
Request for Comments: 9855 Individual
Intended status:
Category: Standards Track S. Litkowski
Expires: 16 August 2025
ISSN: 2070-1721 C. Filsfils
Cisco Systems
P. Francois
INSA Lyon
B. Decraene
Orange
D. Voyer
Bell Canada
12 February
September 2025
Topology Independent Fast Reroute using Using Segment Routing
draft-ietf-rtgwg-segment-routing-ti-lfa-21
Abstract
This document presents Topology Independent Loop-free Loop-Free Alternate (TI-
LFA) Fast Reroute (TI-LFA), (FRR), which is aimed at providing protection of
node and adjacency segments within the Segment Routing (SR)
framework. This Fast
Reroute (FRR) FRR behavior builds on proven IP Fast Reroute FRR concepts being
LFAs, remote Remote LFAs (RLFA), (RLFAs), and remote LFAs with directed forwarding (DLFA).
(DLFAs). It extends these concepts to provide guaranteed coverage in
any two-connected networks using a link-state IGP. An important
aspect of TI-LFA is the FRR path selection approach establishing
protection over the expected post-convergence paths from the point Point of local repair,
Local Repair (PLR), reducing the operational need to control the tie-breaks tie-
breaks among various FRR options.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list It represents the consensus of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid the IETF community. It has
received public review and has been approved for a maximum publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of six months this document, any errata,
and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 16 August 2025.
https://www.rfc-editor.org/info/rfc9855.
Copyright Notice
Copyright (c) 2025 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info)
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
3.
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.
2.1. Abbreviations and Notations
2.2. Conventions used Used in this document . . . . . . . . . . . . 8
4. This Document
3. Base principle . . . . . . . . . . . . . . . . . . . . . . . 8
5. Principle
4. Intersecting P-Space and Q-Space with post-convergence
paths . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1. Post-Convergence Paths
4.1. Extended P-Space property computation Property Computation for a resource X, Resource X over post-convergence paths . . . . . . . . . . . . . . . 8
5.2.
Post-Convergence Paths
4.2. Q-Space property computation Property Computation for a resource X, Resource X over
post-convergence paths . . . . . . . . . . . . . . . . . 9
5.3.
Post-Convergence Paths
4.3. Scaling considerations when computing Considerations When Computing Q-Space . . . . . . 9
6.
5. TI-LFA Repair path . . . . . . . . . . . . . . . . . . . . . 9
6.1. Path
5.1. FRR path using Path Using a direct neighbor . . . . . . . . . . . . 11
6.2. Direct Neighbor
5.2. FRR path using Path Using a PQ node . . . . . . . . . . . . . . . . 11
6.3. Node
5.3. FRR path using Path Using a P node Node and Q node that are adjacent . . 11
6.4. Node That Are Adjacent
5.4. Connecting distant Distant P and Q nodes along post-convergence
paths . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Nodes Along Post-Convergence
Paths
6. Building TI-LFA repair lists Repair Lists for SR Segments . . . . . . . . 11
7.1.
6.1. The active segment is Active Segment Is a node segment . . . . . . . . . . 12
7.2. Node Segment
6.2. The active segment is Active Segment Is an adjacency segment . . . . . . . 12
7.2.1. Adjacency Segment
6.2.1. Protecting [Adjacency, Adjacency] segment lists . . . 13
7.2.2. Segment Lists
6.2.2. Protecting [Adjacency, Node] segment lists . . . . . 13
8. Dataplane specific considerations . . . . . . . . . . . . . . 13
8.1. Segment Lists
7. Dataplane-Specific Considerations
7.1. MPLS dataplane considerations . . . . . . . . . . . . . . 13
8.2. Dataplane Considerations
7.2. SRv6 dataplane considerations . . . . . . . . . . . . . . 14
9. Dataplane Considerations
8. TI-LFA and SR algorithms . . . . . . . . . . . . . . . . . . 14
10. Algorithms
9. Usage of Adjacency segments Segments in the repair list . . . . . . . 15
11. Repair List
10. Security Considerations . . . . . . . . . . . . . . . . . . . 16
12.
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16
13. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 16
14. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 16
15.
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 17
15.1.
12.1. Normative References . . . . . . . . . . . . . . . . . . 17
15.2.
12.2. Informative References . . . . . . . . . . . . . . . . . 17
Appendix A. Advantages of using Using the expected post-convergence path
during Expected Post-Convergence Path
During FRR . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix B. Analysis based Based on real network topologies . . . . . 21 Real Network Topologies
Acknowledgments
Contributors
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 26
2.
1. Introduction
This document outlines a local repair mechanism that leverages
Segment Routing (SR) to restore end-to-end connectivity in the event
of a failure involving a directly connected network component. This
mechanism is designed for standard link-state Interior Gateway
Protocol (IGP) shortest path scenarios. Non-SR mechanisms for local
repair are beyond the scope of this document. Non-local failures are
addressed in a separate document
[I-D.bashandy-rtgwg-segment-routing-uloop]. [SR-LOOP].
The term topology independent Topology Independent (TI) describes the capability providing
a loop free loop-free backup path that is effective accross across all network
topologies. This provides a major improvement compared to LFA
[RFC5286] and remote LFA [RFC7490] RLFA [RFC7490], which cannot provide a complete
protection coverage in some topologies as described in [RFC6571].
When the network reconverges after failure, micro-loops [RFC5715] can
form due to transient inconsistencies in the forwarding tables of
different routers. If it is determined that micro-loops are a
significant issue in the deployment, then a suitable loop-free
convergence method, method should be implemented, such as one of those
described in [RFC5715], [RFC6976], [RFC8333], or [I-D.bashandy-rtgwg-segment-routing-uloop]
should be implemented. [SR-LOOP].
TI-LFA operates locally at the Point of Local Repair (PLR) upon
detecting a failure in one of its direct links. Consequently, this
local operation does not influence:
* Micro-loops that may or may not form during the distributed
Interior Gateway Protocol (IGP) IGP
convergence as delineated in [RFC5715]:
- These micro-loops occur on routes directed towards the
destination that do not traverse TI-LFA-configured paths. paths configured for TI-LFA.
According to [RFC5714], the formation of such micro-loops can
prevent traffic from reaching the PLR, thereby bypassing the
TI-LFA paths established for rerouting.
* Micro-loops that may or may not develop when the previously failed
link is restored to functionality.
TI-LFA paths are activated from the instant the PLR detects a failure
in a local link and remain in effect until the Interior Gateway
Protocol (IGP) IGP convergence at the
PLR is fully achieved. Consequently, they are not susceptible to
micro-loops that may arise due to variations in the IGP convergence
times across different nodes through which these paths traverse.
This ensures a stable and predictable routing environment, minimizing
disruptions typically associated with asynchronous network behavior.
However, an early (relative to the other nodes) IGP convergence at
the PLR and the consecutive ”early” "early" release of TI-LFA paths may cause
micro-loops, especially if these paths have been computed using the
methods described in Section Section 6.2, Section 6.3, Sections 5.2, 5.3, or Section 6.4 5.4 of the this document. One
of the possible ways to prevent such micro-loops is local convergence
delay ([RFC8333]). [RFC8333].
TI-LFA procedures are complementary to the application of any micro-loop micro-
loop avoidance procedures in the case of link or node failure:
* Link or node failure requires some urgent action to restore the
traffic that passed thru through the failed resource. TI-LFA paths are
pre-computed and pre-installed and therefore pre-installed; therefore, they are suitable for
urgent
recovery recovery.
* The paths used in the micro-loop avoidance procedures typically
cannot be pre-computed.
For each destination (as specified by the IGP) in the network, TI-LFA
pre-installs a backup forwarding entry for each protected destination
ready to be activated upon detection of the failure of a link used to
reach the destination. TI-LFA provides protection in the event of
any one of the following: single link failure, single node failure,
or single SRLG Shared Risk Link Group (SRLG) failure. In link failure
mode, the destination is protected assuming the failure of the link.
In node protection mode, the destination is protected assuming that
the neighbor connected to the primary link (see Section 3 2) has
failed. In SRLG protecting mode, the destination is protected
assuming that a configured set of links sharing fate with the primary
link has failed (e.g. (e.g., a linecard or a set of links sharing a common
transmission pipe).
Protection techniques outlined in this document are limited to
protecting links, nodes, and SRLGs that are within a link-state IGP
area. Protecting domain exit routers and/or links attached to
another routing domains are domain is beyond the scope of this document document.
By utilizing Segment Routing (SR), SR, TI-LFA eliminates the need to establish Targeted
Label Distribution Protocol sessions with remote nodes for leveraging
the benefits of Remote Loop-Free Alternates
(RLFA) [RFC7490][RFC7916] (RLFAs) [RFC7490]
[RFC7916] or Directed Loop-Free Alternates (DLFA) (DLFAs) [RFC5714]. All
the Segment Identifiers (SIDs) required are present within the Link
State Database (LSDB) of the Interior Gateway
Protocol (IGP). IGP. Consequently, there is no longer a
necessity to prefer LFAs over RLFAs or DLFAs, nor is there a need to
minimize the number of RLFA or DLFA repair nodes.
Utilizing SR makes the requirement unnecessary to establish an
additional state within the network for enforcing explicit Fast
Reroute (FRR) paths. This spares the nodes from maintaining a
supplementary state and frees the operator from the necessity to
implement additional protocols or protocol sessions solely to augment
protection coverage.
TI-LFA also brings the benefit of the ability to provide a backup
path that follows the expected post-convergence path considering a
particular failure failure, which reduces the need of locally configured
policies that influence the backup path selection ([RFC7916]). [RFC7916]. The
easiest way to express the expected post-convergence path in a loop-
free manner is to encode it as a list of adjacency segments.
However, this may create a long segment list that some hardware may
not be able to program. One of the challenges of TI-LFA is to encode
the expected post-convergence path by combining adjacency segments
and node segments. Each implementation may independently develop its
own algorithm for optimizing the ordered segment list. This document
provides an outline of the fundamental concepts applicable to
constructing the SR backup path, along with the related dataplane
procedures. Appendix A describes contains a more detailed description of some
of the post-convergence path
related aspects of TI-LFA in more detail. related to post-convergence path.
This document is structured as follows:
* Section 3 2 defines the main notations used in the document. They
are in line with [RFC5714].
* Section 4 3 defines the main principles of TI-LFA backup path
computation.
* Section 5 4 suggests to compute the P-Space and Q-Space properties
defined in Section 3, 2 for the specific case of nodes lying over the
post-convergence paths towards the protected destinations.
* Using the properties defined in Section 5, 4, Section 6 5 describes how
to compute protection lists that encode a loop-free post-convergence post-
convergence path towards the destination.
* Section 7 6 defines the segment operations to be applied by the PLR
to ensure consistency with the forwarding state of the repair
node.
* Section 8 7 discusses aspects that are specific to the dataplane.
* Section 9 8 discusses the relationship between TI-LFA and the SR-algorithm. SR
algorithm.
* Certain considerations are needed when adjacency segments are used
in a repare repair list. Section 10 9 provides an overview of these
considerations.
* Section 11 10 discusses security considerations.
* Appendix A highlights advantages of using the expected post-
convergence path during FRR.
* By implementing the algorithms detailed in this document within
actual service provider and large enterprise network environments,
real-life measurements are presented regarding the number of SIDs
utilized by repair paths. These measurements are summarized in
Appendix B.
3.
2. Terminology
1. Acronyms
*
2.1. Abbreviations and Notations
DLFA: Remote LFA with Directed forwarding.
* Loop-Free Alternate
FRR: Fast Re-route.
* Reroute
IGP: Interior Gateway Protocol.
* Protocol
LFA: Loop-Free Alternate.
* Alternate
LSDB: Link State DataBase.
* Database
PLR: Point of Local Repair.
* Repair
RL: Repair list.
* List
RLFA: Remote LFA.
* Loop-Free Alternate
SID: Segment Identifier.
* Identifier
SPF: Shortest Path First.
* First
SPT: Shortest Path Tree
SR: Segment Routing.
* Routing
SRLG: Shared Risk Link Group.
* Group
TI-LFA: Topology Independent LFA. Loop-Free Alternate
The main notations used in this document are defined as follows. follows:
* The terms "old" and "new" topologies refer to the Link State Database
(LSDB) LSDB state
before and after the considered failure, respectively.
* SPT_old(R) is the Shortest Path Tree SPT rooted at node R in the initial state of the
network.
* SPT_new(R, X) is the Shortest Path Tree SPT rooted at node R in the state of the
network after the resource X has failed.
PLR stands for "Point
* The Point of Local Repair". It Repair (PLR) is the router that applies fast
traffic restoration after detecting failure in a directly attached
link, set of links, and/or node.
* Similar to [RFC7490], the concept of P-Space and Q-Space is used
for TI-LFA.
* The P-space P(R,X) of a router R with regard to a resource X (e.g.
(e.g., a link S-F, a node F, or a an SRLG) is the set of routers
reachable from R using the pre-convergence shortest paths without
any of those paths (including equal-cost path splits) transiting
through X. A P node is a node that belongs to the P-space.
* Consider the set of neighbors of a router R and a resource X.
Exclude from that set, set the neighbors that are reachable from R
using X. The Extended extended P-Space P'(R,X) of a node R with regard to
a resource X is the union of the P-spaces of the neighbors in that
reduced set of neighbors with regard to the resource X.
* The Q-space Q(R,X) of a router R with regard to a resource X is
the set of routers from which R can be reached without any path
(including equal-cost path splits) transiting through X. A Q node
is a node that belongs to the Q-space Q-space.
* EP(P, Q) is an explicit SR path from a node P to a node Q.
Primary Interface: Primary Outgoing Interface: One
* The primary interface and primary outgoing interface are one of
the outgoing interfaces towards a destination according to the IGP
link-state
protocol
Primary Link: A protocol.
* The primary link is a link connected to the primary interface
adj-sid(S-F): Adjacency Segment interface.
* The adj-sid(S-F) is the adjacency segment from node S to node F
3.1. F.
2.2. Conventions used Used in this document This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
4.
3. Base principle Principle
The basic algorithm to compute the repair path is to pre-compute
SPT_new(R,X) and and, for each destination, encode the repair path as a
loop-free segment list. One way to provide a loop-free segment list
is to use adjacency SIDs only. However, this approach may create
very long SID lists that hardware may not be able to handle due to
MSD (Maximum
Maximum SID Depth) Depth (MSD) limitations.
An implementation is free to use any local optimization to provide
smaller segment lists by combining Node SIDs and Adjacency SIDs. In
addition, the usage of Node-SIDs allow to maximize for maximizing ECMPs over the
backup path. These optimizations are out of scope of this document,
however document;
however, the subsequent sections provide some guidance on how to
leverage P-Spaces and Q-Spaces to optimize the size of the segment
list.
5.
4. Intersecting P-Space and Q-Space with post-convergence paths Post-Convergence Paths
One of the challenges of defining an SR path following the expected
post-convergence path is to reduce the size of the segment list. In
order to reduce this segment list, an implementation MAY determine
the P-Space/Extended P-Space / extended P-Space and Q-Space properties (defined in
[RFC7490]) of the nodes along the expected post-convergence path from
the PLR to the protected destination and compute an SR explicit path
from P to Q when they are not adjacent. Such properties will be used
in Section 6 5 to compute the TI-LFA repair list.
5.1.
4.1. Extended P-Space property computation Property Computation for a resource X, Resource X over post-
convergence paths Post-
Convergence Paths
The objective is to determine which nodes on the post-convergence
path from the PLR R to the destination D are in the extended P-space
of R with regard to resource X (where X can be a link or a set of
links adjacent to the PLR, PLR or a neighbor node of the PLR).
This can be found by:
* Excluding excluding neighbors which that are not on the post-convergence path when
computing P'(R,X) P'(R,X), then
* Then, intersecting the set of nodes belonging to the post-
convergence post-convergence
path from R to D, assuming the failure of X, with P'(R, X).
5.2.
4.2. Q-Space property computation Property Computation for a resource X, Resource X over post-
convergence paths Post-
Convergence Paths
The goal is to determine which nodes on the post-convergence path
from the Point of Local Repair (PLR) R to the destination D are in
the Q-Space of destination D with regard to resource X (where X can
be a link or a set of links adjacent to the PLR, or a neighbor node
of the PLR).
This can be found by intersecting the set of nodes belonging to the
post-convergence path from R to D, assuming the failure of X, with
Q(D, X).
5.3.
4.3. Scaling considerations when computing Considerations When Computing Q-Space
[RFC7490] raises scaling concerns about computing a Q-Space per
destination. Similar concerns may affect TI-LFA computation if an
implementation tries to compute a reverse Shortest Path Tree
([RFC7490]) (SPT)
[RFC7490] for every destination in the network to determine the
Q-Space. It will be up to each implementation to determine the good
tradeoff between scaling and accuracy of the optimization.
6.
5. TI-LFA Repair path Path
The TI-LFA repair path consists of an outgoing interface and a list
of segments (repair list (a Repair List (RL)) to insert on the SR header in
accordance with the dataplane used. The repair list encodes the
explicit, and possibly post-convergence, path to the destination,
which avoids the protected resource X and, at the same time, is
guaranteed to be loop-free irrespective of the state of FIBs along
the nodes belonging to the explicit path as long as the states of the
FIBs are programmed according to a link-state IGP. Thus, there is no
need for any co-ordination coordination or message exchange between the PLR and any
other router in the network.
The TI-LFA repair path is found by intersecting P(S,X) and Q(D,X)
with the post-convergence path to D and computing the explicit SR-
based path EP(P, Q) from a node P in P(S,X) to a node Q in Q(D,X)
when these nodes are not adjacent along the post convergence post-convergence path.
The TI-LFA repair list is expressed generally as (Node-SID(P), EP(P,
Q)).
S ------- N1 ----------- D
*\ | \ |
* \ | \ |
* \ | \ |
* N2-----R1****R2 *** R3
* *
N3 *********
***** : link with high metric (1k)
----- : link with metric 1
Figure 1: Sample topology Topology with TI-LFA
As an example, in Figure 1, the focus is on the TI-LFA backup from S
to D, considering the failure of node N1.
* First, P(S, N1) is computed and results in [N3, N2, R1].
* Then, Q(D, N1) is computed and results in [R3].
* The expected post-convergence path from S to D considering the
failure of N1 is <N2 -> R1 -> R2 -> R3 -> D> (we are naming it
PCPath
"PCPath" in this example).
* P(S, N1) intersection with PCPath is [N2, R1], R1]. With R1 being the
deeper downstream node in PCPath, it can be assumed to be used as
a P node (this is an example example, and an implementation could use a
different strategy to choose the P node).
* Q(D, N1) intersection with PCPath is [R3], so R3 is picked as a Q
node. An SR explicit SR-explicit path is then computed from R1 (P node) to R3
(Q node) following PCPath (R1 -> R2 -> R3): <Adj-Sid(R1-R2), Adj-
Sid(R2-R3)>.
As a result, the TI-LFA repair list of S for destination D
considering the failure of node N1 is: <Node-SID(R1), Adj-Sid(R1-R2),
Adj-Sid(R20R3)>.
Adj-Sid(R2-R3)>.
Most often, the TI-LFA repair list has a simpler form, as described
in the following sections. Appendix B provides statistics for the
number of SIDs in the explicit path to protect against various
failures.
6.1.
5.1. FRR path using Path Using a direct neighbor Direct Neighbor
When a direct neighbor is in P(S,X) and Q(D,x) Q(D,x), and the link to that
direct neighbor is on the post-convergence path, the outgoing
interface is set to that neighbor and the repair segment list is
empty.
This is comparable to a post-convergence LFA FRR repair.
6.2.
5.2. FRR path using Path Using a PQ node Node
When a remote node R is in P(S,X) and Q(D,x) and on the post-
convergence path, the repair list is made of a single node segment to
R
R, and the outgoing interface is set to the outgoing interface used
to reach R.
This is comparable to a post-convergence RLFA repair tunnel.
6.3.
5.3. FRR path using Path Using a P node Node and Q node that are adjacent Node That Are Adjacent
When a node P is in P(S,X) and a node Q is in Q(D,x) Q(D,x), and both are on
the post-convergence path and both are adjacent to each other, the repair
list is made of two segments: A a node segment to P (to be processed
first), followed by an adjacency segment from P to Q.
This is comparable to a post-convergence DLFA (LFA with directed
forwarding) repair tunnel.
6.4.
5.4. Connecting distant Distant P and Q nodes along post-convergence paths Nodes Along Post-Convergence Paths
In some cases, there is no adjacent P and Q node along the post-
convergence path. As mentioned in Section 4, 3, a list of adjacency
SIDs can be used to encode the path between P and Q. However, the
PLR can perform additional computations to compute a list of segments
that represent a loop-free path from P to Q. How these computations
are done is out of scope of this document and is left to
implementation.
7.
6. Building TI-LFA repair lists Repair Lists for SR Segments
The following sections describe how to build the repair lists using
the terminology defined in [RFC8402]. The procedures described in
this section are equally applicable to both SR-MPLS the Segment Routing over
MPLS (SR-MPLS) and SRv6 the Segment Routing over IPv6 (SRv6) dataplane,
while the dataplane-specific considerations are described in
Section 8.
In this section, 7.
This section explains the process by which a protecting router S
handles the active segment of a packet upon the failure of its
primary outgoing interface for the packet, S-F, is explained. packet S-F. The failure of the
primary outgoing interface may occur due to various triggers, such as
link failure, neighbor node failure, and others.
7.1.
6.1. The active segment is Active Segment Is a node segment Node Segment
The active segment MUST be kept on the SR header unchanged and the
repair list MUST be added. The active segment becomes the first
segment after the repair list. The way the repair list is added
depends on the dataplane used (see Section 8).
7.2. 7).
6.2. The active segment is Active Segment Is an adjacency segment
The Adjacency Segment
This section defines the FRR behavior applied by S for any packet
received with an active adjacency segment S-F, S-F for which protection
was enabled, is defined
here. enabled. Since protection has been enabled for the segment S-F
and signaled in the IGP (for instance, using protocol extensions from
[RFC8667] and [RFC8665]), a calculator of any SR policy utilizing
this segment is aware that it may be transiently rerouted out of S-F
in the event of an S-F failure.
The simplest approach for link protection of an adjacency segment S-F
is to create a repair list that will carry the traffic to F. To do
so, one or more “PUSH” "PUSH" operations are performed. If the repair list,
while avoiding S-F, terminates on F, S only pushes segments of the
repair list. Otherwise, S pushes a node segment of F, followed by
the segments of the repair list. For details on the "NEXT" and
"PUSH" operations, refer to [RFC8402].
This method, which merges back the traffic at the remote end of the
adjacency segment, has the advantage of keeping as much traffic as
possible
the traffic on the pre-failure path. When SR policies are involved and
strict compliance with the policy is required, an end-to-end
protection (beyond the scope of this document) should be preferred
over the local repair mechanism described above.
Note, however, that when the SR source node is using traffic
engineering Traffic
Engineering (TE), it will generally not be possible for the PLR to
know what post-convergence path will be selected by the source node
once it detects the failure, since computation of the TE path is a
local matter that depends on constraints that may not be known at the
PLR. Therefore, no method applied at the PLR can guarantee
protection will follow the post-convergence path.
The case where the active segment is followed by another adjacency
segment is distinguished from the case where it is followed by a node
segment. Repair techniques for the respective cases are provided in
the following subsections.
7.2.1.
6.2.1. Protecting [Adjacency, Adjacency] segment lists Segment Lists
If the next segment in the list is an Adjacency segment, then the
packet has to be conveyed to F.
To do so, S MUST apply a "NEXT" operation on Adj-Sid(S-F) and then
one or more “PUSH” "PUSH" operations. If the repair list, while avoiding
S-F, terminates on F, S only pushes the segments of the repair list.
Otherwise, S pushes a node segment of F, followed by the segments of
the repair list. For details on the "NEXT" and "PUSH" operations,
refer to [RFC8402].
Upon failure of S-F, a packet reaching S with a segment list matching
[adj-sid(S-F),adj-sid(F-M),...] will thus leave S with a segment list
matching [RL(F),node(F),adj-sid(F-M),...], where RL(F) is the repair
list for destination F.
7.2.2.
6.2.2. Protecting [Adjacency, Node] segment lists Segment Lists
If the next segment in the stack is a node segment, say for node T,
the segment list on the packet matches [adj-sid(S-F),node(T),...].
In this case, S MUST apply a "NEXT" operation on the Adjacency
segment related to S-F, followed by a "PUSH" of a repair list
redirecting the traffic to a node Q, whose path to node segment T is
not affected by the failure.
Upon failure of S-F, packets reaching S with a segment list matching
[adj-sid(S-F), node(T), ...], ...] would leave S with a segment list
matching [RL(Q),node(T), ...].
8. Dataplane specific considerations
8.1.
7. Dataplane-Specific Considerations
7.1. MPLS dataplane considerations Dataplane Considerations
The MPLS dataplane for Segment Routing (SR) is described in
[RFC8660].
The following dataplane behaviors apply when creating a repair list
using an MPLS dataplane:
1. If the active segment is a node segment that has been signaled
with penultimate hop popping popping, and the repair list ends with an
adjacency segment terminating on a node that advertised NEXT the
"NEXT" operation [RFC8402] of the active segment, then the active
segment MUST be popped before pushing the repair list.
2. If the active segment is a node segment segment, but the other conditions
in 1. are not met, the active segment MUST be popped and then
pushed again with a label value computed according to the Segment
Routing Global Block (SRGB) of Q, where Q is the endpoint of the
repair list. Finally, the repair list MUST be pushed.
8.2.
7.2. SRv6 dataplane considerations Dataplane Considerations
SRv6 dataplane and programming instructions are described
respectively in [RFC8754] and [RFC8986].
The TI-LFA path computation algorithm is the same as in the SR-MPLS
dataplane. Note however Note, however, that the Adjacency SIDs are typically
globally routed. In such a case, there is no need for preceding an
adjacency SID with a Prefix-SID [RFC8402] [RFC8402], and the resulting repair
list is likely shorter.
If the traffic is protected at a Transit Node, then an SRv6 SID list
is added on the packet to apply the repair list. The addition of the
repair list follows the headend head-end behaviors as specified in section Section 5
of [RFC8986].
If the traffic is protected at an SR Segment Endpoint Node, first the
Segment Endpoint packet processing is executed. Then Then, the packet is
protected as if its it were a transit packet.
9.
8. TI-LFA and SR algorithms Algorithms
SR allows an operator to bind an algorithm to a prefix-SID Prefix-SID (as
defined in [RFC8402]. [RFC8402]). The algorithm value dictates how the path to
the prefix is computed. The SR default algorithm is known has as the
"Shortest Path" algorithm. The SR default algorithm allows an
operator to override the IGP shortest path by using local policies.
When TI-LFA uses Node-SIDs associated with the default algorithm,
there is no guarantee that the path will be loop-free loop-free, as a local
policy may have overriden overridden the expected IGP path. As the local
policies are defined by the operator, it becomes the responsibility
of this operator to ensure that the deployed policies do not affect
the TI-LFA deployment. It should be noted that such a situation can
already happen today with existing mechanisms such as remote LFA. RLFA.
[RFC9350] defines a flexible algorithm (FlexAlgo) Flexible Algorithm framework to be associated
with Prefix-SIDs. FlexAlgo A Flexible Algorithm allows a user to associate a
constrained path to a Prefix-SID rather than using the regular IGP
shortest path. An implementation MAY support TI-LFA to protect Node-
SIDs associated with a Flex Algo. Flexible Algorithm. In such a case, rather
than computing the expected post-convergence path based on the
regular SPF, an implementation SHOULD use the constrained SPF
algorithm bound to the Flex Algo Flexible Algorithm (using the Flex Algo Flexible
Algorithm Definition) instead of the regular Dijkstra in all the SPF/rSPF SPF/
rSPF computations that are occurring during the TI-LFA computation.
This includes the computation of the P-Space and Q-Space as well as
the post-convergence path. Furthermore, the implementation SHOULD
only use Node-SIDs/Adj-SIDs bound to the Flex Algo Flexible Algorithm and/or
unprotected Adj-SIDs of the regular SPF to build the repair list.
The use of regular Dijkstra for the TI-LFA computation or for
building of the repair path using SIDs other than those recommended does
not ensure that the traffic going over the TI-LFA repair path during
the fast-reroute FRR period is honoring the Flex Algo Flexible Algorithm constraints.
10.
9. Usage of Adjacency segments Segments in the repair list Repair List
The repair list of segments computed by TI-LFA may contain one or
more adjacency segments. An adjacency segment may be protected or
not protected.
S --- R2 --- R3 ---- R4 --- R5 --- D
* | \ *
* | \ *
R7 ** R8
* |
* |
R9 -- R10
Figure 2
In Figure 2, all the metrics are equal to 1 except
R2-R7,R7-R8,R8-R4,R7-R9
R2-R7,R7-R8,R8-R4,R7-R9, which have a metric of 1000. Considering R2
as a PLR to protect against the failure of node R3 for the traffic
S->D, the repair list computed by R2 will be [adj-sid(R7-R8),adj-
sid(R8-R4)]
sid(R8-R4)], and the outgoing interface will be to R7. If R3 fails,
R2 pushes the repair list onto the incoming packet to D. During the
FRR, if R7-R8 fails and if TI-LFA has picked a protected adjacency
segment for adj-sid(R7-R8), R7 will push an additional repair list
onto the packet following the procedures defined in Section 7. 6.
To avoid the possibility of this double FRR activation, an
implementation of TI-LFA MAY pick only non protected non-protected adjacency
segments when building the repair list. However, this it is important to
note that FRR in general is intended to protect for a single pre-
planned failure. If the failure that happens is worse than expected
or multiple failures happen, FRR is not guaranteed to work. In such
a case, fast IGP convergence remains important to restore traffic as
quickly as possible.
11.
10. Security Considerations
The techniques described in this document are internal
functionalities to a router that can guarantee an upper bound on the
time taken to restore traffic flow upon the failure of a directly
connected link or node. As these techniques steer traffic to the
post-convergence path as quickly as possible, this serves to minimize
the disruption associated with a local failure failure, which can be seen as
a modest security enhancement. The protection mechanisms mechanism does not
protect external destinations, but rather provides quick restoration
for destination destinations that are internal to a routing domain.
Security
The security considerations described in [RFC5286] and [RFC7490]
apply to this document. Similarly, as the solution described in the this
document is based on Segment Routing SR technology, the reader should be aware of the
security considerations related to this technology ([RFC8402]) (see [RFC8402])
and its dataplane instantiations ([RFC8660], [RFC8754] (see [RFC8660], [RFC8754], and
[RFC8986]). However, this document does not introduce additional
security
concern.
12. concerns.
11. IANA Considerations
No requirements for
This document has no IANA
13. Contributors
In addition to the authors listed on the front page, the following
co-authors have also contributed to this document:
* Francois Clad, Cisco Systems
* Pablo Camarillo, Cisco Systems
14. Acknowledgments
The authors would like to thank Les Ginsberg, Stewart Bryant,
Alexander Vainsthein, Chris Bowers, Shraddha Hedge, Wes Hardaker,
Gunter Van de Velde and John Scudder for their valuable comments.
15. actions.
12. References
15.1.
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7916] Litkowski, S., Ed., Decraene, B., Filsfils, C., Raza, K.,
Horneffer, M., and P. Sarkar, "Operational Management of
Loop-Free Alternates", RFC 7916, DOI 10.17487/RFC7916,
July 2016, <https://www.rfc-editor.org/info/rfc7916>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
July 2018, <https://www.rfc-editor.org/info/rfc8402>.
[RFC8660] Bashandy, A., Ed., Filsfils, C., Ed., Previdi, S.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing with the MPLS Data Plane", RFC 8660,
DOI 10.17487/RFC8660, December 2019,
<https://www.rfc-editor.org/info/rfc8660>.
[RFC8754] Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J.,
Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header
(SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020,
<https://www.rfc-editor.org/info/rfc8754>.
[RFC8986] Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer,
D., Matsushima, S., and Z. Li, "Segment Routing over IPv6
(SRv6) Network Programming", RFC 8986,
DOI 10.17487/RFC8986, February 2021,
<https://www.rfc-editor.org/info/rfc8986>.
15.2.
12.2. Informative References
[I-D.bashandy-rtgwg-segment-routing-uloop]
Bashandy, A., Filsfils, C., Litkowski, S., Decraene, B.,
Francois, P., and P. Psenak, "Loop avoidance using Segment
Routing", Work in Progress, Internet-Draft, draft-
bashandy-rtgwg-segment-routing-uloop-17, 29 June 2024,
<https://datatracker.ietf.org/doc/html/draft-bashandy-
rtgwg-segment-routing-uloop-17>.
[RFC5286] Atlas, A., Ed. and A. Zinin, Ed., "Basic Specification for
IP Fast Reroute: Loop-Free Alternates", RFC 5286,
DOI 10.17487/RFC5286, September 2008,
<https://www.rfc-editor.org/info/rfc5286>.
[RFC5714] Shand, M. and S. Bryant, "IP Fast Reroute Framework",
RFC 5714, DOI 10.17487/RFC5714, January 2010,
<https://www.rfc-editor.org/info/rfc5714>.
[RFC5715] Shand, M. and S. Bryant, "A Framework for Loop-Free
Convergence", RFC 5715, DOI 10.17487/RFC5715, January
2010, <https://www.rfc-editor.org/info/rfc5715>.
[RFC6571] Filsfils, C., Ed., Francois, P., Ed., Shand, M., Decraene,
B., Uttaro, J., Leymann, N., and M. Horneffer, "Loop-Free
Alternate (LFA) Applicability in Service Provider (SP)
Networks", RFC 6571, DOI 10.17487/RFC6571, June 2012,
<https://www.rfc-editor.org/info/rfc6571>.
[RFC6976] Shand, M., Bryant, S., Previdi, S., Filsfils, C.,
Francois, P., and O. Bonaventure, "Framework for Loop-Free
Convergence Using the Ordered Forwarding Information Base
(oFIB) Approach", RFC 6976, DOI 10.17487/RFC6976, July
2013, <https://www.rfc-editor.org/info/rfc6976>.
[RFC7490] Bryant, S., Filsfils, C., Previdi, S., Shand, M., and N.
So, "Remote Loop-Free Alternate (LFA) Fast Reroute (FRR)",
RFC 7490, DOI 10.17487/RFC7490, April 2015,
<https://www.rfc-editor.org/info/rfc7490>.
[RFC8333] Litkowski, S., Decraene, B., Filsfils, C., and P.
Francois, "Micro-loop Prevention by Introducing a Local
Convergence Delay", RFC 8333, DOI 10.17487/RFC8333, March
2018, <https://www.rfc-editor.org/info/rfc8333>.
[RFC8665] Psenak, P., Ed., Previdi, S., Ed., Filsfils, C., Gredler,
H., Shakir, R., Henderickx, W., and J. Tantsura, "OSPF
Extensions for Segment Routing", RFC 8665,
DOI 10.17487/RFC8665, December 2019,
<https://www.rfc-editor.org/info/rfc8665>.
[RFC8667] Previdi, S., Ed., Ginsberg, L., Ed., Filsfils, C.,
Bashandy, A., Gredler, H., and B. Decraene, "IS-IS
Extensions for Segment Routing", RFC 8667,
DOI 10.17487/RFC8667, December 2019,
<https://www.rfc-editor.org/info/rfc8667>.
[RFC9256] Filsfils, C., Talaulikar, K., Ed., Voyer, D., Bogdanov,
A., and P. Mattes, "Segment Routing Policy Architecture",
RFC 9256, DOI 10.17487/RFC9256, July 2022,
<https://www.rfc-editor.org/info/rfc9256>.
[RFC9350] Psenak, P., Ed., Hegde, S., Filsfils, C., Talaulikar, K.,
and A. Gulko, "IGP Flexible Algorithm", RFC 9350,
DOI 10.17487/RFC9350, February 2023,
<https://www.rfc-editor.org/info/rfc9350>.
[SR-LOOP] Bashandy, A., Filsfils, C., Litkowski, S., Decraene, B.,
Francois, P., and P. Psenak, "Loop avoidance using Segment
Routing", Work in Progress, Internet-Draft, draft-
bashandy-rtgwg-segment-routing-uloop-17, 29 June 2024,
<https://datatracker.ietf.org/doc/html/draft-bashandy-
rtgwg-segment-routing-uloop-17>.
Appendix A. Advantages of using Using the expected post-convergence path
during Expected Post-Convergence Path
During FRR
[RFC7916] raised raises several operational considerations when using LFA or
remote LFA. [RFC7916]
RLFA. Section 3 of [RFC7916] presents a case where a high bandwidth
link between two core routers is protected through a PE Provider Edge
(PE) router connected with low bandwidth links. In such a case,
congestion may happen when the FRR backup path is activated.
[RFC7916] introduces a local policy framework to let the operator
tuning manually the best alternate election based on its own
requirements.
From a network capacity planning point of view, it is often assumed
for simplicity that if a link L fails on a particular node X, the
bandwidth consumed on L will be spread over some of the remaining
links of X. The remaining links to be used are determined by the IGP
routing considering that the link L has failed (we assume that the
traffic uses the post-convergence path starting from the node X). In
Figure 3, we consider a network with all metrics equal to 1 except
the metrics on links used by PE1, PE2 PE2, and PE3 PE3, which are 1000. An
easy network capacity planning method is to consider that if the link
L (X-B) fails, the traffic actually flowing through L will be spread
over the remaining links of X (X-H, X-D, X-A). Considering the IGP
metrics, only X-H and X-D can be used in reality to carry the traffic
flowing through the link L. As a consequence, the bandwidth of links
X-H and X-D is sized according to this rule. We should observe that
this capacity planning policy works, however works; however, it is not fully
accurate.
In Figure 3, considering that the source of traffic is only from PE1
and PE4, when the link L fails, depending on the convergence speed of
the nodes, X may reroute its forwarding entries to the remote PEs
onto X-H or X-D; however however, in a similar timeframe, PE1 will also
reroute a subset of its traffic (the subset destined to PE2) out of
its nominal path path, reducing the quantity of traffic received by X.
The capacity planning rule presented previously has the drawback of
oversizing the network, however network; however, it allows to prevent for preventing any
transient congestion (when for example (for example, when X reroutes traffic before PE1
does).
H --- I --- J
| | \
PE4 | | PE3
\ | (L) | /
A --- X --- B --- G
/ | | \
PE1 | | PE2
\ | | /
C --- D --- E --- F
Figure 3
Based on this assumption, in order to facilitate the operation of
FRR, FRR
and limit the implementation of local FRR policies, traffic can be
steered by the PLR onto its expected post-convergence path during the
FRR phase. In our example, when link L fails, X switches the traffic
destined to PE3 and PE2 on the post-convergence paths. This is
perfectly inline in line with the capacity planning rule that was presented
before and also inline in line with the fact that X may converge before PE1
(or any other upstream router) and may spread the X-B traffic onto
the post-convergence paths rooted at X.
It should be noted, noted that some networks may have a different capacity
planning rule, leading to an allocation of less bandwidth on X-H and
X-D links. In such a case, using the post-convergence paths rooted
at X during FRR may introduce some congestion on X-H and X-D links.
However
However, it is important to note, note that a transient congestion may
possibly happen, happen even without FRR activated, for instance instance, when X
converges before the upstream routers. Operators are still free to
use the policy framework defined in [RFC7916] if the usage of the
post-convergence paths rooted at the PLR is not suitable.
Readers should be aware that FRR protection is pre-computing a backup
path to protect against a particular type of failure (link, node, or
SRLG). When using the post-convergence path as an FRR backup path,
the computed post-convergence path is the one considering the failure
we are protecting against. This means that FRR is using an expected
post-convergence path, and this expected post-convergence path may be
actually different from the post-convergence path used if the failure
that happened is different from the failure FRR was protecting
against. As an example, if the operator has implemented a protection
against a node failure, the expected post-convergence path used
during FRR will be the one considering that the node has failed.
However, even if a single link is failing or a set of links is
failing (instead of the full node), the node-protecting post-
convergence path will be used. The consequence is that the path used
during FRR is not optimal with respect to the failure that has
actually occurred.
Another consideration to take into account is: while is as follows: While using
the expected post-convergence path for SR traffic using node segments
only (for instance, PE to PE traffic using the shortest path) has
some advantages, these advantages reduce when SR policies ([RFC9256]) [RFC9256]
are involved. A segment-list segment list used in an SR policy is computed to
obey a set of path constraints defined locally at the head-end or
centrally in a controller. TI-LFA cannot be aware of such path constraints
constraints, and there is no reason to expect the TI-LFA backup path
protecting one
segments segment in that segment list to obey those
constraints. When SR policies are used and the operator wants to
have a backup path which that still follows the policy requirements, this
backup path should be computed as part of the SR policy in the
ingress node (or central
controller) controller), and the SR policy should not
rely on local protection. Another option could be to use FlexAlgo ([RFC9350]) a Flexible
Algorithm [RFC9350] to express the set of constraints and use a
single node segment associated with a
FlexAlgo Flexible Algorithm to reach the
destination. When using a node segment associated with a FlexAlgo, Flexible
Algorithm, TI-LFA keeps providing an optimal backup by applying the
appropriate set of constraints. The relationship between TI-LFA and
the SR-algorithm SR algorithm is detailed in Section 9. 8.
Appendix B. Analysis based Based on real network topologies Real Network Topologies
This section presents an analysis performed on real service provider
and large enterprise network topologies. The objective of the
analysis is to assess the number of SIDs required in an explicit path
when the mechanisms described in this document are used to protect
against the failure scenarios within the scope of this document. The
number of segments described in this section are applicable to
instantiating
segment routing SR over the MPLS forwarding plane.
The measurement below indicate that indicates that, for link and local SRLG
protection, a 1 SID 1-SID repair path delivers more than 99% coverage. For
node protection protection, a 2 SIDs 2-SID repair path yields 99% coverage.
Table 1 below lists the characteristics of the networks used in our
measurements. The number of links refers to the number of
"bidirectional" links (not directed edges of the graph). The
measurements are carried out as follows:
* For each network, the algorithms described in this document are
applied to protect all prefixes against link, node, and local SRLG
failure
failure.
* For each prefix, the number of SIDs used by the repair path is
recorded
recorded.
* The percentage of number of SIDs are listed in Tables 2A/B, 3A/B, 2, 3, 4, 5,
6, and 4A/B 7.
The measurements listed in the tables indicate that for link and
local SRLG protection, 1 SID a 1-SID repair path is sufficient to protect
more than 99% of the prefix in almost all cases. For node protection
2 SIDs
protection, 2-SID repair paths yield 99% coverage.
+-------------+------------+------------+------------+------------+
+=========+=======+=======+====================+============+
| Network | Nodes | Links |Node-to-Link| SRLG info? |
| | | | Node-to-Link Ratio | SRLG Info? |
+-------------+------------+------------+------------+------------+
+=========+=======+=======+====================+============+
| T1 | 408 | 665 | 1.63 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T2 | 587 | 1083 | 1.84 | No |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T3 | 93 | 401 | 4.31 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T4 | 247 | 393 | 1.59 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T5 | 34 | 96 | 2.82 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T6 | 50 | 78 | 1.56 | No |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T7 | 82 | 293 | 3.57 | No |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T8 | 35 | 41 | 1.17 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
| T9 | 177 | 1371 | 7.74 | Yes |
+-------------+------------+------------+------------+------------+
+---------+-------+-------+--------------------+------------+
Table 1: Data Set Definition
The rest of this section presents the measurements done on the actual
topologies. The convention conventions that we use is are as follows follows:
* 0 SIDs: the The calculated repair path starts with a directly
connected neighbor that is also a loop free alternate, loop-free alternate; in which
case
case, there is no need to explicitly route the traffic using
additional SIDs. This scenario is described in Section 6.1. 5.1.
* 1 SIDs: the SID: The repair node is a PQ node, node; in which case case, only 1 SID is
needed to guarantee a loop-free path. This scenario is covered in
Section 6.2. 5.2.
* 2 or more SIDs: The repair path consists of 2 or more SIDs as
described in Section 6.3 Sections 5.3 and Section 6.4. 5.4. We do not cover the case for 2
SIDs (Section 6.3) 5.3) separately because there was no granularity in
the result. Also Also, we treat the node-SID+adj-SID node-SID + adj-SID and node-SID +
node-SID the same because they do not differ from the data plane
point of view.
Table 2A
Tables 2 and 2B 3 below summarize the measurements on the number of SIDs
needed for link protection
+-------------+------------+------------+------------+------------+ protection.
+=========+========+=======+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs |
+-------------+------------+------------+------------+------------+
+=========+========+=======+========+========+
| T1 | 74.3% | 25.3% | 0.5% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T2 | 81.1% | 18.7% | 0.2% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T3 | 95.9% | 4.1% | 0.1% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T4 | 62.5% | 35.7% | 1.8% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T5 | 85.7% | 14.3% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T6 | 81.2% | 18.7% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T7 | 98.9% | 1.1% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T8 | 94.1% | 5.9% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T9 | 98.9% | 1.0% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
Table 2A: 2: Link protection (repair size distribution)
+-------------+------------+------------+------------+------------+ Protection (Repair Size
Distribution)
+=========+========+========+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs |
+-------------+------------+------------+------------+------------+
+=========+========+========+========+========+
| T1 | 74.2% | 99.5% | 99.9% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T2 | 81.1% | 99.8% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T3 | 95.9% | 99.9% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T4 | 62.5% | 98.2% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T5 | 85.7% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T6 | 81.2% | 99.9% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T7 | 98,8% 98.8% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T8 | 94,1% 94.1% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T9 | 98,9% 98.9% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
Table 2B: 3: Link protection repair size cumulative distribution
Table 3A Protection (Repair Size
Cumulative Distribution)
Tables 4 and 3B 5 summarize the measurements on the number of SIDs
needed for local SRLG protection.
+-------------+------------+------------+------------+------------+
+=========+========+=======+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs |
+-------------+------------+------------+------------+------------+
+=========+========+=======+========+========+
| T1 | 74.2% | 25.3% | 0.5% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T2 | No SRLG Information information |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T3 | 93.6% | 6.3% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T4 | 62.5% | 35.6% | 1.8% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T5 | 83.1% | 16.8% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T6 | No SRLG Information information |
+-------------+---------------------------------------------------+
+---------+----------------------------------+
| T7 | No SRLG Information information |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T8 | 85.2% | 14.8% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
| T9 | 98,9% 98.9% | 1.1% | 0.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+-------+--------+--------+
Table 3A: 4: Local SRLG protection repair size distribution
+-------------+------------+------------+------------+------------+ Protection (Repair
Size Distribution)
+=========+========+========+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs |
+-------------+------------+------------+------------+------------+
+=========+========+========+========+========+
| T1 | 74.2% | 99.5% | 99.9% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T2 | No SRLG Information information |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T3 | 93.6% | 99.9% | 100.0% | 0.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T4 | 62.5% | 98.2% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T5 | 83.1% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T6 | No SRLG Information information |
+-------------+---------------------------------------------------+
+---------+-----------------------------------+
| T7 | No SRLG Information information |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T8 | 85.2% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
| T9 | 98.9% | 100.0% | 100.0% | 100.0% |
+-------------+------------+------------+------------+------------+
+---------+--------+--------+--------+--------+
Table 3B: 5: Local SRLG protection repair size Protection (Repair Size
Cumulative distribution Distribution)
The remaining two tables summarize the measurements on the number of
SIDs needed for node protection.
+---------+----------+----------+----------+----------+----------+
+=========+========+=======+========+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs | 4 SIDs |
+---------+----------+----------+----------+----------+----------+
+=========+========+=======+========+========+========+
| T1 | 49.8% | 47.9% | 2.1% | 0.1% | 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T2 | 36,5% 36.5% | 59.6% | 3.6% | 0.2% | 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T3 | 73.3% | 25.6% | 1.1% | 0.0% | 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T4 | 36.1% | 57.3% | 6.3% | 0.2% | 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T5 | 73.2% | 26.8% | 0% 0.0% | 0% 0.0% | 0% 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T6 | 78.3% | 21.3% | 0.3% | 0% 0.0% | 0% 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T7 | 66.1% | 32.8% | 1.1% | 0% 0.0% | 0% 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T8 | 59.7% | 40.2% | 0% 0.0% | 0% 0.0% | 0% 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
| T9 | 98.9% | 1.0% | 0% 0.0% | 0% 0.0% | 0% 0.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+-------+--------+--------+--------+
Table 4A: 6: Node protection (repair size distribution)
+---------+----------+----------+----------+----------+----------+ Protection (Repair Size Distribution)
+=========+========+========+========+========+========+
| Network | 0 SIDs | 1 SID | 2 SIDs | 3 SIDs | 4 SIDs |
+---------+----------+----------+----------+----------+----------+
+=========+========+========+========+========+========+
| T1 | 49.7% | 97.6% | 99.8% | 99.9% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T2 | 36.5% | 96.1% | 99.7% | 99.9% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T3 | 73.3% | 98.9% | 99.9% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T4 | 36.1% | 93.4% | 99.8% | 99.9% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T5 | 73.2% | 100.0% | 100.0% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T6 | 78.4% | 99.7% | 100.0% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T7 | 66.1% | 98.9% | 100.0% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T8 | 59.7% | 100.0% | 100.0% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
| T9 | 98.9% | 100.0% | 100.0% | 100.0% | 100% 100.0% |
+---------+----------+----------+----------+----------+----------+
+---------+--------+--------+--------+--------+--------+
Table 4B: 7: Node protection (repair size cumulative distribution) Protection (Repair Size Cumulative
Distribution)
Acknowledgments
The authors would like to thank Les Ginsberg, Stewart Bryant,
Alexander Vainsthein, Chris Bowers, Shraddha Hedge, Wes Hardaker,
Gunter Van de Velde, and John Scudder for their valuable comments.
Contributors
In addition to the authors listed on the front page, the following
co-authors have also contributed to this document:
Francois Clad
Cisco Systems
Pablo Camarillo
Cisco Systems
Authors' Addresses
Ahmed Bashandy
Individual
Email: abashandy.ietf@gmail.com
Stephane Litkowski
Cisco Systems
France
Email: slitkows@cisco.com
Clarence Filsfils
Cisco Systems
Brussels
Belgium
Email: cfilsfil@cisco.com
Pierre Francois
INSA Lyon
Email: pierre.francois@insa-lyon.fr
Bruno Decraene
Orange
Issy-les-Moulineaux
France
Email: bruno.decraene@orange.com
Daniel Voyer
Bell Canada
Canada
Email: daniel.voyer@bell.ca